(蒸汽疏水器)杆杠浮球式疏水阀

(蒸汽疏水器)进口杆杠浮球式疏水阀主要性能 Main performance

杆杠浮球式蒸汽疏水阀浮球带动杠杆自动调节排水座阀孔的开度，工作连续，蒸汽压力变化时不受影响，工作稳定，可实现小体积大容量的连续排水，主要用于蒸汽管网和蒸汽加热设备自动阻汽排水  RETZ Rod rod float ball steam trap: the float ball drives the lever to automatically adjust the opening of the valve hole of the drain seat. It works continuously and is not affected when the steam pressure changes. It works stably and can realize continuous drainage with small volume and large capacity. It is mainly used for automatic steam blocking and drainage of steam pipe network and steam heating equipment

设计标准:ISO6552；EN26704  Design standard: iso6552; EN26704

连接长度∶EN26554；GB/T12250 Connection length: EN26554; GB/T12250

试验与检验∶EN26948；GB/T12251 Test and inspection: en26948; GB/T12251

规格尺寸：1/2-4"(法兰、内螺纹RC、NPT)  Specification and size: 1 / 2-4 "(flange, internal thread RC, NPT)

公称压力：16-40Bar Nominal pressure: 16-40bar

使用压差范围:0.1-32Bar Operating pressure difference range: 0.1-32bar

介质温度：≤300℃  Medium temperature: ≤ 300 ℃

性能曲线图 Performance curves

上图中的冷凝水排量是基于饱和温度下的，在蒸汽设备刚开机状态时冷凝水为冷态，疏水阀内部热静力排空气阀打开可额外增加冷凝水的排量。

FT14(DN15 DN20 DN25 1/2"3/4" 1") 压差bar（×100=KPa）

FT43、FT44(DN15 DN20 DN32 DN40 DN50) 压差bar（×100=KPa）

FT43、FT44（DN50，DN65）高排量型 压差bar（×100=KPa）

(蒸汽疏水器)进口杆杠浮球式疏水阀特点∶ Performance characteristics

内置自动排空气装置，启动迅速，无空气气堵，排除不可凝结气体性能好 RETZ Built in automatic air exhaust device, quick start, no air blockage, good performance in eliminating non condensable gas

该阀能迅速自动地连续排放饱和凝结水，保证加热设备内不会有水积聚，从而获得最高加热效率 The valve can rapidly and automatically discharge the saturated condensate continuously to ensure that there is no water accumulation in the heating equipment, so as to obtain the highest heating efficiency

排水阀座孔始终在凝结水水位以下，形成水封，工作时无新鲜蒸汽泄漏  The valve can rapidly and automatically discharge the saturated condensate continuously to ensure that there is no water accumulation in the heating equipment, so as to obtain the highest heating efficiency

单阀座杠杆浮球式蒸汽疏水阀球面密封无集中磨损，关闭阀座孔时，具有软着陆特点，提高寿命 The spherical seal of the single seat lever floating ball steam trap has no centralized wear. When the valve seat hole is closed, it has the characteristics of soft landing and improves the service life

背压率大于90%，便于凝结水回收  The back pressure rate is greater than 90%, which is convenient for condensate recovery

密封性能好，漏气率低，节能效果好 Good sealing performance, low air leakage rate and remarkable energy saving effect

安装灵活，即可立式安装，也可水平安装 Flexible installation, either vertical or horizontal

主要零件材料 Main parts and materials

1.阀体GGG40/A216 WCB/A351CF8 

2.阀盖GGG40/A216 WCB/A351CF8

3.螺栓A193 B7

4.阀盖垫片A240 304+石墨

5.浮球A240304 

6.阀芯A276 430 

7.挡水板A240 304

8.排空气装置组件： A、膜盒 A240 304  B、弹簧17-4PH  C、膜盒支撑片A240 304  D、膜盒阀座 17-4PH  E、膜盒固定罩 A240 304 

9.阀座螺栓A193 B8 

10.支架 A240 304 

11.阀座A276  430

安装示意图 Installation diagram

请按阀体上流向箭头所示安装，注意浮球臂处于水平位置以确保其能垂直升降 Please install as shown by the flow arrow on the valve body. Note that the float arm is in the horizontal position to ensure that it can rise and fall vertically