(吊桶)倒置桶蒸汽疏水阀

(吊桶)进口倒置桶蒸汽疏水阀 主要性能 Main performance

倒置桶蒸汽疏水阀采用球面密封，拉杆耐磨损性好，阀芯更深地陷入阀座，从而保持了密封性，阀芯支架与特殊设计而成的"超级杠杆"相配合。阀芯在支架内是自由浮动的，避免了关闭时产生的刚性碰撞 RETZ inverted bucket steam drain valve adopts spherical seal, with good wear resistance of the pull rod. The valve core is deeper into the valve seat, so as to maintain the tightness. The valve core support is matched with the specially designed "super lever". The valve core is free floating in the bracket to avoid rigid collision during closing

规格尺寸：1/2-3"(法兰/内螺纹BSP、NPT)  Specification and size: 1 / 2-3 "(flange / internal thread BSP, NPT)

公称压力：16-40Bar Nominal pressure: 16-40bar

压差范围:0.1-30Bar Operating pressure difference range: 0.1-30bar

介质温度：≤300℃  Medium temperature: ≤ 300 ℃

性能曲线图 Performance curves  压差bar（×100=KPa）

881/881F DN15~DN25

882/882F DN15~DN25

883/883F DN25~DN50

885/885F DN40~DN80

特点∶ Performance characteristics

可承受高背压，可达90%  Can withstand high back pressure, up to 90%

抗水击∶开口吊桶结构不会因水击而遭损坏  Water hammer resistance: the open bucket structure will not be damaged by water hammer

阀体内设有滤网，且阀瓣与阀座位于阀体的顶部，污物不会存积在阀孔处  The valve body is provided with a filter screen, and the valve disc and the valve seat are located at the top of the valve body. Dirt will not be accumulated at the valve hole

球面密封无集中磨损，关闭阀座孔时，由于采用了浮动杠杆机构，具有软着陆特点，提高了使用寿命  The spherical seal has no concentrated wear. When the valve seat hole is closed, the floating lever mechanism is adopted, which has the characteristics of soft landing and improves the service life

独特的杠杆机构将倒置桶重力放大，以便开启受到系统压差作用的阀瓣。杠杆机构为自由浮动式，没有固定支点造成的磨损  The unique lever mechanism enlarges the gravity of the inverted bucket to open the valve disc affected by the system pressure difference. The lever mechanism is free floating, without wear caused by fixed fulcrum

排放口完全被水封包围，可防止新鲜蒸汽损失 The discharge port is completely surrounded by water seal to prevent the loss of fresh steam

倒置桶疏水阀排放动作是间断的，但其凝结水排放是连续的，不存在凝结水的积聚问题 RETZ The discharge action of the inverted bucket drain valve is intermittent, but the condensate discharge is continuous, and there is no accumulation of condensate

(吊桶)进口倒置桶蒸汽疏水阀 主要零件材料 Main parts and materials

1.阀体GGG40/A216 WCB/A351 CF8 

2.阀盖GGG40/A216 WCB/A351 CF8 

3.堵头ASTM A105 

4.阀盖螺栓A193 B7 

5.套圈A276 304 

6.阀芯导杆A276 304 

7.连杆螺栓A194 B8 

8.阀座A276 430 

9.阀芯A276 430 

10.阀芯连杆A276 304 

11.阀芯固定片A240 304 

12.吊桶 A240 304

13.过滤网A240 304 

14.过滤器堵头ASTM A105

安装示意图 Installation diagram

请按阀体上流向箭头所示安装，注意疏水阀处于水平位置或低于设备出口，以保证正常疏水 Please install as shown by the flow arrow on the valve body. Note that the drain valve is at the horizontal position or lower than the equipment outlet to ensure normal drainage