首页 > 产品中心 > RETZ阀门/(瑞茨) > 水力控制阀 > 短长度法兰蝶阀 短体法兰蝶阀

短长度法兰蝶阀 短体法兰蝶阀

简要描述:RETZ进口短长度法兰蝶阀采用中线型设计,具有安装、维修方便等特点。可广泛应用于给排水,暖通系统等流体管线上作为调节或截流装置使用

  • 品牌:RETZ
  • 工况条件:开/关
  • 温度/压力:P-T: 16bar@100℃
  • 更新时间:2023/04/22
产品详情 在线咨询

技术参数 Technical Parameter进口短长度法兰蝶阀2.jpg

进口短长度法兰蝶阀,短体法兰蝶阀是用圆盘式启闭件往复回转90°左右来开启、关闭或调节介质流量的一种阀门,阀板与阀轴的高精度加工确保了持久有效的负载传输

Imported short length flange butterfly valve, short body flange butterfly valve is a type of valve that uses a disc type opening and closing element to rotate back and forth by about 90 ° to open, close, or adjust the medium flow rate. The high-precision processing of the valve plate and valve shaft ensures long-lasting and effective load transmission


公称通径:DN50-DN1200


结构长度:GB/T12221、
EN 558 Series 20、 ISO 5752 Series 20 、API 609 Table 1


连接法兰:GB/T9113PN10/16
、DIN 2501 PN10/16 、ASME Class 150、 AWWA C 207 、AS 2129 Talbe D and E 、JIS B2238 10K


密封等级:GB/T13927
、EN 12266 (Leakage rate A)、API 598(Table 5)、ISO 5208, Category 3


工作温度:-20℃ to +180℃(取决于压力、介质和材料)

工作压力:16bar


阀座材料介质说明Description of valve seat material medium

阀座材料介质说明.jpg

材料

适用介质

不适用介质

三元乙丙
EPDM

水、蒸汽、酒精、乙二醇、烧碱、臭氧、食品、甘油、牛奶、氧气、空气、饱和盐、氯化铁、明胶、干热氢硫化物、氯化钾、氯化钠、氯化镁

矿物油、氯化合物、酮、乙酰基、氯化物、沥青、溴、
丁烷、丁基、汽油、柴油、酸、鱼油、氟里昂、氯、
天然气、废气、硝酸

丁晴橡胶
NBR

矿物油、润滑脂、空气、海水、气体、硼酸、氯化铝、氨气、柠檬酸、柴油、鱼油、汽油、明胶、甘油、氯化镁、乳酸、亚麻子油、天然气

臭氧、丙酮、苯胺、二氧化氯、铬酸、苯酚、乙基乙酸乙酯、氟利昂212223、热硝酸、苯乙烯、硫化氢、乙酸异丙酯、氧气、硫酸

天然橡胶
Natural Rubber

研磨介质、氯化铝、甜菜液、硼酸、钾氯化物、柠檬酸、
氯化镁、硝酸铁、甲酸、明胶、糖、甘油、乳酸、氮

蒸汽、苯胺、沥青、丁二烯、柴油、乙烷、乙酸乙酯、
液压油、盐酸、亚麻子油、甲烷、矿物油、氧气、
苯乙烯、大豆油、松节油

海帕伦
Hypalon

矿物、有机和无机化学品、空气、氧气、鱼油、甘油、
柠檬酸、臭氧、溶剂酸钠

氨、柴油、润滑脂、酮、甲基、苯酚、丙基、溴、
硝酸、焦油、尿素、清漆、芦丁

硅橡胶
Silicone

食品、氨气、钡、硼酸、钾、亚硫酸氢盐、柠檬酸、氰化铜、甘油、氮气、乳酸

蒸汽和热水(最高100摄氏度)、沥青、柴油、乙烷、
氟里昂、乙基氯、甲烷、硝酸、橄榄油、丙烷、松节油

氟橡胶
FPM

石油、矿物酸、油脂、磷、单宁酸、明胶、乙二醇、氧气、熟石灰、碳酸氢盐、天然气、纸浆、盐、糖、硫

热水、蒸汽、酮、氨气、丙酮、甲醛、醋酸纤维素、
氟里昂、尿素、甲基丙烯酸

氟橡胶FPM-B

酸、碱、胺热水、蒸汽

汽油、石脑油、烃类溶剂、氯溶剂


为多样化的工况应用选择合适的阀板材料 Choose appropriate valve plate materials for diverse operating conditions

为多样化的工况应用选择合适的阀板材料.jpg

扭矩值:
下表所列扭矩值为干燥介质在20℃空气中测量所得:Torque value:
The torque values listed in the following table are measured in 20℃ air


下表所列参数值为阀门启动扭矩(阀板与阀座分离,扭矩值下降)。
数据仅供参考,受压力、温度等因素影响,数据会有偏差

The parameter values listed in the following table are the valve starting torque (the valve plate is separated from the valve seat and the torque value decreases).
Data are for reference only, due to pressure, temperature and other factors, the data will be biased

DN(mm)

50

65

80

100

125

150

200

250

300

350

400

450

500

600

700

750

800

900

1000

Siez(inch)

2

212

3

4

5

6

8

10

12

14

16

18

20

24

28

30

32

36

40

MD(Nm)

9

18

24

37

59

125

200

240

360

700

850

1500

2255

3390

4410

5810

6600

7100

11500

零部件列表及材质说明 Parts List and Material Description

零部件列表及材质说明.jpg

序号

 

 

序号

名称

 

 

序号

材料

1

阀体

球墨铸铁

EN1563 JS1030

3

阀座

NBR

-15℃~+85℃

4

阀轴

SS420

碳钢

ASTM A216 WCB

X-NBR

-15℃~+85℃

SS431

不锈钢

ASTM A351 CF8M

NBR-DVGW

-15℃~+60℃

17-4PH

2

阀板

不锈钢

ASTM A351 CF8

EPDM

-20℃~+120℃

5

阀杆固定环

SS304

ASTM A351 CF8M

EPDM-H

-20℃~+130℃

SS316

ASTM A351 CF3M

EPDM FDA(白色)

-20℃~+110℃

6

阀杆轴套

/PTFE

合金钢

2507

EPDM-H FDA(黑色)

-20℃~+130℃

7

Y型密封环

NBR

1.4462

EPDM WRAS

-20℃~+110℃

8

E型扣环

SS304

1.4529

FPM

-15℃~+180℃

9

螺丝钉

SS304

1.4539

FPM-B

-15℃~+180℃

SS316

哈氏合金


铝青铜

C95800

球墨铸铁

Rilsan, Halar coated


不可忽视的蝶阀安装要点Main points of installation butterfly valve

1、要求使用对焊法兰,不建议采用平焊法兰,因为钢管伸进平焊法兰,容易碰到阀板,影响阀板自由启闭Recommend to use butt welding flange. Do not use flat welding flange because steel pipe can easily meet disc to affect opening and closing freely disc if steel pipe enter flat welding flange.

2、确认法兰尺寸必须允许阀板自由转动,法兰内径不能过小或过大 The inner diameter of flange can't be too small or too big and must confirm the dimension of flange so that the disc can turn free. 

3、蝶阀装上后不允许再焊接法兰,以免烫伤衬圈 For avoiding scalding the seat, do not weld flange after the butterfly valve was installed in pipe.

不可忽视的蝶阀安装要点.jpg

产品中心
相关产品