不锈钢电动调节阀

进口不锈钢电动调节阀 技术参数 Technical paramete

电动调节阀应用在暖通空调系统中，在能量的输配和维持水循环系统的水力平衡方面起到非常重要的作用。主要配合末端执行机构，从控制系统接收控制信号和调节阀杆的信号值，而执行器则根据信号值调节阀门开度，改变管网系统的流量 retz品牌  Electric control valve is used in HVAC system, which plays a very important role in energy transmission and distribution and maintaining the hydraulic balance of water circulation system. It mainly cooperates with the end effector to receive the control signal from the control system and adjust the signal value of the valve rod, while the actuator adjusts the valve opening according to the signal value to change the flow of the pipe network system

结构特性：二通/三通分流/三通合流 Structure: two-way / three-way diversion / three-way confluence

备注∶DN15~DN50三通阀仅有合流阀，如果需要分流接法，请对调阀门A口与AB口，按阀体标牌指示操作 Remarks: DN15 ~ DN50 three-way valve is only a confluence valve. If it needs to be connected by shunt, please adjust port a and port ab of the valve, and operate according to the valve body label

进口不锈钢电动调节阀 规格说明 Description

内螺纹连接  Internal thread connection

阀体材质∶304非磁性不锈钢，不锈钢阀杆，V型免维护补偿密封，聚四氟乙烯密封阀芯 Valve body material: 304 non-magnetic stainless steel, stainless steel valve stem, V-type maintenance free compensation seal, polytetrafluoroethylene sealing valve core

连接口径∶G1/2~G2-1/2 Connection diameter: G1/2~G2-1/2

阀体承压∶4.0MPa  Pressure bearing of valve body: 4.0Mpa

阀杆密封∶EPDM密封 Stem seal: EPDM seal

介质温度∶0~120℃ Medium temperature: 0 ~ 120 ℃

工作介质∶冷/热水，浓度<50%的乙二醇溶液 Working medium: cold / hot water, glycol solution with concentration < 50%

流量特性∶等百分比 Flow characteristics: equal percentage

阀泄漏率∶小于KVS值的0~0.05%  Valve leakage rate: less than 0 ~ 0.05% of kVs value

驱动材质∶压铸合金铝支架，钢质传动齿轮，同步马达，浮动式开关 Driving material: die casting alloy aluminum bracket, steel transmission gear, synchronous motor, floating switch

工作电源∶AC24V/AC220V50/60HZ  Working power supply: AC24V / AC220V 50 / 60Hz

驱动控制∶浮点型，智能型（DC0~10V/4~20mA），开关型，选配无源反馈 Drive control: floating point type, intelligent type (dc0 ~ 10V / 4 ~ 20mA), switch type, optional passive feedback

输出扭力∶1200N，带断电手动开关功能 Output torque: 1200n, with power-off manual switch function

法兰连接 Flange connection

阀体材质 ：304非磁性不锈钢，不锈钢阀芯阀杆，V型免维护补偿密封  Valve body material: 304 non-magnetic stainless steel, stainless steel valve core and stem, V-type maintenance free compensation seal

连接口径 ：F2"~12"（法兰连接）Connection diameter: F2 "~ 12" (flange connection)

阀体承压：1.6MPa；2.5MPa Pressure bearing of valve body: 1.6Mpa; 2.5MPa

密封材质：PTFE+碳纤维  Sealing material: PTFE + carbon fiber

介质温度：-20~95°C（300°C可定制）Medium temperature: - 20 ~ 95 ° C (300 ° C can be customized)

工作介质：冷/热水、蒸汽、热导油、腐蚀性介质 Working medium: cold / hot water, steam, thermal oil, corrosive medium

流量特性 ：等百分比 Flow characteristics: equal percentage

阀泄漏率：小于KVS值的0~0.05% Valve leakage rate: less than 0 ~ 0.05% of kVs value

驱动材质 ：压铸合金铝支架，钢质传动齿轮，同步马达，浮动式开关 Driving material: die casting alloy aluminum bracket, steel transmission gear, synchronous motor, floating switch

工作电源 ：AC24V/AC220V 50/60Hz  Working power supply: AC24V / AC220V 50 / 60Hz

驱动控制 ：浮点型，智能型（DC0~10V/4~20mA)，温控一体型（带485通信，空调主机联动），开关型，选配无源反馈  Drive control: floating point type, intelligent type (dc0 ~ 10V / 4 ~ 20mA), temperature control integrated type (with 485 communication, linkage of air conditioning host), switch type, optional passive feedback

输出扭力 ：1200N~5000N，带断电手动开关功能  Output torque: 1200n ~ 5000n, with power-off manual switch function

流量特性 Flow characteristics

性能特点∶ Performance characteristics

等百分比控制特性，比传统的调节阀体控制精度高  Equal percentage control characteristic, higher control accuracy than traditional regulating valve body

电子预设定功能，便于现场调试，系统运行具有更高的效率  Electronic preset function, convenient for on-site debugging, and higher efficiency of system operation

具有故障自动诊断和报警功能，电源带过载保护功能  With automatic fault diagnosis and alarm function, the power supply has overload protection function

安装说明 Installation instructions

1.注意阀门介质流向应与管路介质流向一致  Note: the flow direction of valve medium shall be consistent with that of pipeline medium

2.阀门可以安装在供水或回水管路上，一般推荐安装在回水管路上（安装在回水管路上可以使水流控制更为平稳，同时热水回水部分的温度较低，可延长阀门使用寿命），同时推荐在阀门前安装过滤器和止回阀。当介质为蒸汽时，管道上安装排水阀，可以除去凝结水，否则将影响阀门使用寿命  The valve can be installed on the water supply or return pipeline. It is generally recommended to install it on the return pipeline (the installation on the return pipeline can make the water flow control more stable, and the temperature of the hot water return part is low, which can prolong the service life of the valve). At the same time, it is recommended to install a filter and a check valve in front of the valve. When the medium is steam, a drain valve is installed on the pipeline to remove the condensed water, otherwise the service life of the valve will be affected

3.注意阀门安装方向 Pay attention to the installation direction of the valve