首页 > 产品中心 > RETZ联轴器/(瑞茨)机械传动 > 进口鼓形齿式联轴器 > 垂直安装鼓形齿式联轴器(WGC)

垂直安装鼓形齿式联轴器(WGC)

简要描述：RETZ进口垂直安装鼓形齿式联轴器(WGC)相对于直齿联轴器来说可允许大的角位移，可齿的接触条件，提高传递转矩的能力，延长使用寿命

品牌：RETZ
工况条件：联接机械
温度/压力：710-160000N.m.
更新时间：2023/03/27

联系我们

产品详情 在线咨询

进口垂直安装鼓形齿式联轴器(WGC) 产品用途 Product use 进口垂直安装鼓形齿式联轴器(WGC)2.jpg

具有角位移时沿齿宽的接触状态，由齿数相同的内齿圈和带外齿的凸缘半联轴器等零件组成，在工作时，两轴产生相对角位移，内外齿的齿面周期性作轴向相对滑动，必然形成齿面磨损和功率消耗，因此，WGC垂直安装鼓形齿式联轴器需在有良好和密封的状态下工作。WGC垂直安装鼓形齿式联轴器同齿式联轴器一样径向尺寸小，承载能力大，常用于低速重载工况条件的轴系传动，并经动平衡的齿式联轴器可用于高速传动。

The contact state along the tooth width with angular displacement is composed of internal gear rings with the same number of teeth, flange half couplings with external teeth, and other components. During operation, relative angular displacement occurs between the two shafts, and the tooth surfaces of the internal and external teeth periodically slide axially relative to each other, inevitably resulting in tooth surface wear and power consumption. Therefore, WGC vertically installed drum gear couplings need to operate in a good and sealed state. WGC vertically mounted drum gear couplings have the same radial size and large load carrying capacity as gear couplings. They are commonly used in shafting transmission under low speed and heavy load conditions, and dynamically balanced gear couplings can be used for high-speed transmission.

基本参数 Basic parameters and dimensions

进口垂直安装鼓形齿式联轴器(WGC)结构图.jpg

型号	额定转矩 N·m	许用转速 rpm	轴孔直径 d1、d2	轴孔长度L	D	D1	D2	D4	D3	B	B1	C		转动惯量 kg·m²		重量kg
				Y								Ⅰ	Ⅱ	Ⅰ	Ⅱ	Ⅰ	Ⅱ
WGC1	710	7500	12,14	32	122	115	98	88	60	116	100	30	—	0.0079	0.0064	5.8	5.1
			16,18,19	42								20	14
			20,22,24	52								10	6
			25,28	62								6
			30,32,35,38	82
			40,42	112
WGC2	1250	6700	22,24	52	150	145	118	108	77	136	104	20	7	0.022	0.017	10	7.9
			25,28	62								10
			30,32,35,38	82								7
			40,42,45,48, 50,55,56	112
WGC3	2500	6300	22,24	52	170	165	140	125	90	160	108	33	7	0.047	0.033	17	12.8
			25,28	62								23
			30,32,35,38	82								7
			40,42,45,48, 50,55,56	112
			60,63	142
WGC4	4500	5600	30,32,35,38	82	200	195	160	145	112	180	116	13	7	0.099	0.074	20.5	20.5
			40,42,45,48, 50,55,56	112								7
			60,63,65, 70,71,75	142
			80	172
WGC5	7100	5300	30,32,35,38	82	225	215	180	168	128	200	126	23	8	0.177	0.13	36.1	27.7
			40,42,45,48, 50,55,56	112								8
			60,63,65, 70,71,75	142
			80,85,90	172

号	额定转矩 N·m	许用转速 rpm	轴孔直径 d1、d2	轴孔长度L	D	D1	D2	D4	D3	B	B1	C		转动惯量 kg·m²		重量kg
				Y								Ⅰ	Ⅱ	Ⅰ	Ⅱ	Ⅰ	Ⅱ
WGC6	10000	5000	30,32,35,38	82	245	230	200	185	145	224	134	35	10	0.3	0.22	53.2	39.8
			40,42,45,48, 50,55,56	112								10
			60,63,65, 70,71,75	142
			80,85,90,95	172
			100	212
WGC7	14000	4500	32,35,38	82	272	265	230	210	160	244	148	45	10	0.53	0.35	71.1	47.5
			40,42,45,48, 50,55,56	112								15
			60,63,65, 70,71,75	142								10
			80,85,90,95	172
			100,110	212
WGC8	20000	4250	55,56	112	290	272	245	225	176	272	162	29	10	0.72	0.47	83	59.6
			60,63,65,70, 71,75	142								10
			80,85,90,95	172
			100,110, 120,125	212
WGC9	25000	4000	65,70,71,75	142	315	305	265	245	190	280	176	10	10	1.06	0.8	110	85
			80,85,90,95	172
			100,110,125	212
			130,140	252
WGC 10	40000	3550	75	142	355	340	300	280	225	330	196	28	10	1.77	1.56	164	128
			80,85,90,95	172								10
			100,110,120, 125	212
			130,140,150	252
			160	302
WGC 11	56000	3000	85,90,95	172	412	385	345	325	256	360	224	15	14	3.76	2.88	224	178
			110,110,120, 125	212								14
			130,140,150	252
			160,170,180	302
WGC 12	80000	2800	120,125	212	440	435	375	360	288	414	250	14	14	6.55	4.93	315	255
			130,140,150	252
			160,170,180	302
			190,200	352
WGC 13	112000	2500	140,150	252	490	480	425	400	320	470	272	14	14	10.6	8	406	325
			160,170,180	302
			190,200,220	352
WGC 14	160000	2300	160,170,180	302	545	540	462	440	362	530	316	16	16	17.8	13.9	542	423
			190,200,220	352
			240,250,260	410

注：质量与转动惯量是按最大轴孔直径Y型轴孔计算的近似值。

Note: Mass and rotational inertia are approximate values calculated based on the maximum shaft hole diameter, Y-shaped shaft hole

产品名称：

您的姓名：

联系电话：

具体内容：

验证码：

产品中心