流量控制阀

简要描述:RETZ进口流量控制阀主要安装在配水管路需要控制流量的管路中,将上游的高压降为低压,保持预定的流量不变,将过大流量限制在一个预定值,即使上游的压力变化,也不影响主阀下游的流量

  • 品牌:RETZ
  • 工况条件:流量控制
  • 温度/压力:P-T: 25bar@100℃
  • 更新时间:2023/04/14
产品详情 在线咨询

产品描述 Product Description进口流量控制阀2.jpg

进口流量控制阀阀体采用了全通道流线设计,流体阻力小,流量大,在转动方式上采用了水力操作,即利用管路中的水压自动操作主阀瓣的上下移动,控制阀口开度,主阀安装在送配水管路控制流量的管线中。可先设定调正阀门上部向导调节阀及导阀某一固定流量,就可使通过主阀的流量保持不变,即使主阀上游的压力发生变化,也不会影响。总之该产品是生活给水、消防系统及工业给水系统的理想产品。

The inlet flow control valve body adopts a full channel streamline design, with low fluid resistance and high flow rate. In terms of rotation, hydraulic operation is adopted, which uses the water pressure in the pipeline to automatically operate the up and down movement of the main valve disc and control the valve opening. The main valve is installed in the pipeline for controlling flow in the supply and distribution water pipeline. You can first set a fixed flow rate for the upper guide regulating valve and guide valve of the adjustment valve to maintain the flow rate through the main valve unchanged, even if the pressure upstream of the main valve changes, it will not affect it. In short, this product is an ideal product for domestic water supply, fire protection systems, and industrial water supply systems.


结构和主要零件材质 Structure and main component materials

流量控制阀可分膜片式和活塞式,由主阀、导阀、向导调节阀、针阀、球阀、微型过滤器和压力表等组成,由于导阀、针阀和压力表等要用外接导管与主阀相连接,所以统称为导管控制系统。

Flow control valves can be divided into diaphragm type and piston type, consisting of main valve, pilot valve, guide regulating valve, needle valve, ball valve, micro filter, and pressure gauge. Due to the need for external conduits to connect the pilot valve, needle valve, and pressure gauge to the main valve, they are collectively referred to as conduit control systems.

结构图.jpg

主要零件材质 Main component materials

编号No.

零件名称Name

Material

1

阀盖
Bonnet

灰铸铁、球墨铸铁、碳素钢、不锈钢
Gray casting ironSpheroidal Graphite CastironCarbon steel,Stainless Steel

2

压缩弹簧
Compression Spring

    硅锰钢、铬钒钢、不锈钢
Siico-manganese steelChromium vanadium steelStainless Steel

3

膜片压板
Diaphragm Pressing Plate

  黄铜、碳素钢、球墨铸铁
   BrassCarbon  steelSpheroidal Graphite Cast lron

4

膜片
Diaphragm

          丁晴橡胶
Nitrile-butadiene Rubber(NBR)

5

阀杆
Valve Stem

    不锈钢
Stainless Steel

6

阀板
Valve board

  黄铜、碳素钢、球墨铸铁
   BrassCarbon  steelSpheroidal Graphite Cast Iron

7

密封圈
Sealing Ring

         丁晴橡胶
Nitrile-butadiene Rubber(NBR)

8

阀座
Valve seat

       黄铜、不锈钢、碳素钢
BrassStainless SteelCarbon steel

9

阀板压板
Valve board pressing plate

  黄铜、碳素钢、球墨铸铁
   BrassCarbon  steelSpheroidal Graphite Cast lron

10

阀体
Valve Body

灰铸铁、球墨铸铁、碳素钢、不锈钢
Gray casting ironSpheroidal Graphite Cast lronCarbon steelStainless Steel

工作原理 working principle

当主阀进口端水压分别进入阀体及控制室(参看结构图),且主阀外部之球阀15同时关闭,此时主阀处于全闭状态。当主阀外部工作原理图.jpg之球阀15全开后,控制室内水压全部排出至下游低压区,此时主阀呈现全开状态。调节主阀外部之球阀15开度,使水流经过针阀8与球阀15之水流达到平衡,此时主阀处于浮动状态。

When the water pressure at the inlet end of the main valve enters the valve body and control room respectively (see structural diagram), and the ball valve 15 outside the main valve is closed simultaneously, the main valve is in a fully closed state. When the ball valve 15 outside the main valve is fully open, all the water pressure in the control room is discharged to the downstream low-pressure area, and the main valve is in a fully open state. Adjust the opening of ball valve 15 outside the main valve to balance the water flow between needle valve 8 and ball valve 15. At this time, the main valve is in a floating state

流量控制阀是利用水流通过导管和针阀8进入主阀控制室的压差,引管至并借助调节导阀13的弹簧控制阀门开度,并且调节主阀上部向导调节阀12使主阀保证设定开度,使管线中的流量不超过某一设定值。即使上游压力发生变化,也不会影响下游的压力。(这是膜片式的工作原理,活塞式相同。)

The flow control valve utilizes the pressure difference between the water flow through the conduit and needle valve 8 to enter the main valve control room. The pipe is led to and the valve opening is controlled by the spring of the regulating valve 13. The upper guide regulating valve 12 of the main valve is adjusted to ensure the set opening of the main valve, so that the flow in the pipeline does not exceed a certain set value. Even if the upstream pressure changes, it will not affect the downstream pressure. (This is the working principle of the diaphragm type, and the piston type is the same.)


全关闭状态:当主阀进口端水压分别进入阀体及控制室,且主阀的外部球阀同时关闭,此时主阀处于关闭状态。关闭状态.jpg

Fully closed state: When the water pressure at the inlet end of the main valve enters the valve body and control room respectively, and the external ball valve of the main valve is closed at the same time, the main valve is in a fully closed state


全开启状态:当主阀外部的球阀全开后,此时控制室内水压全部释放到管路下游,而主阀也呈现为开启状态。

Fully open state: When the ball valve outside the main valve is fully open, all the water pressure in the control room is released to the downstream of the pipeline, and the main valve also shows a fully open state

全开启状态.jpg

浮动调节状态:调节主阀外部的球阀开度,使进水端流向控制室的水流和控制室流向下游的水流达到平衡,此时主阀处于调节浮动状态。

Floating adjustment state: Adjust the opening of the ball valve outside the main valve to balance the water flow from the inlet end to the control room and the water flow from the control room to the downstream. At this time, the main valve is in the floating adjustment state

浮动调节状态.jpg

流量示意图 Flow diagram

流量示意图.jpg

安装与调试 Installation and debugging

安装与调试.jpg

1、主阀应水平卧式安装,安装前要彻底清除管道内的杂物。要注意主阀体外水流标示箭头,遵循方向安装。安装后应确保没有管路应力作用在阀体及阀内部件上。

2、主阀前要装一只闸阀和一只过流器,主阀后也要装一只闸阀,以便于维修。

3、导阀与导管控制系统已于出厂前装配和调整完毕,如导阀出厂设定值不适合现场要求,可通过拧紧或放松导阀上端螺钉来调节,顺时针护动螺钉为增加压力,逆时针拧动螺钉为减少压力,调节完后拧紧锁紧螺母。

4、主阀上部向导调节阀,可通过拧紧或放松调节阀上端调节螺杆来调节,顺时针拧动螺杆为减少开度,逆时针拧动螺杆为增加开度。

5、主阀上的微型过流器要定期清洗

6、通水前的须冲洗管路系统。

7、对重要给水管路应安装旁通阀。


产品中心
相关产品