(动态)内螺纹压差平衡阀

技术参数 Technical paramete

(动态)进口内螺纹压差平衡阀当系统管网压差增大，内螺纹动态压差平衡阀依靠自身高低压腔压力变化，使作用于膜片两侧的力重新平衡，同时带动阀杆运动减小阀门开度，吸收增大的资用压差，保证被控制侧的压差恒定RETZ  When the pressure difference of the system pipe network increases, the internal thread dynamic pressure difference balancing valve relies on the pressure change of its high and low pressure chambers to rebalance the force acting on both sides of the diaphragm, drive the valve rod to move to reduce the valve opening, absorb the increased pressure difference of the resources, and ensure that the pressure difference on the controlled side is constant.

尺寸：G1/2"-2"  Size: G1/2 "- 2"

工作温度：-10~100℃  Working temperature: -10 ~ 100 ℃

承压等级：PN16  Pressure bearing grade: PN16 

控制精度∶  ±8%  Control accuracy: ± 8%

最大工作压差∶≤300KPa  Maximum working pressure difference: ≤ 300kPa

工作介质∶冷热水、乙/丙二醇溶液 Working medium: cold and hot water, ethylene / propylene glycol solution

连接方式∶内螺纹 Connection method: internal thread

(动态)进口内螺纹压差平衡阀 性能特点∶ Performance characteristics

自力式压差控制，不需要外部动力源，恒定被控压差 RETZ Self operated differential pressure control, without external power source, constant controlled differential pressure

可现场设定压差值，可控压差范围广  The pressure difference can be set on site, and the controllable pressure difference range is wide

手轮带有压差设定指示，具有关断功能  The handwheel is provided with a pressure difference setting indication and a shut-off function

压力测量口，配有三通测量接头  Pressure measuring port with tee measuring connector

零部件材质 Component material

①阀体：黄铜  Valve body: Brass

②阀座：黄铜  Valve seat: Brass

③阀芯：黄铜  Valve core: Brass

④测量：嘴黄铜  Measurement: nozzle brass

⑤阀杆：黄铜  Valve stem: Brass

⑥弹簧：不锈钢  Spring: stainless steel

⑦膜片：EPDM   Diaphragm: EPDM

⑧手轮：塑料ABS   Handwheel plastic ABS

工作范围

A.KVmin   B.KVnom   C.KVmax   D.工作范围△P∶±25%

安装说明 Installation instructions

内螺纹动态压差平衡阀可以单独使用，亦可与静态平衡阀配合使用。水流方向需与阀体箭头方向符合一致。安装之前应当冲洗管路，并建议在前端安装过滤器。毛细管应连接在供水管路的上方或水平处，但不可位于管路下方，以防被灰尘微粒堵塞，水系统打压测试之前，必须把毛细信号管安装连接好并且旋转阻断阀。否则压力过大会导致压差调节器的损坏 RETZ internal thread dynamic differential pressure balancing valve can be used alone or in combination with static balancing valve. The water flow direction shall be consistent with the arrow direction of the valve body. The pipeline should be flushed before installation, and it is recommended to install a filter at the front end. The capillary shall be connected above or at the level of the water supply pipeline, but not below the pipeline to prevent it from being blocked by dust particles. Before the pressure test of the water system, the capillary signal pipe must be installed and connected and the blocking valve must be rotated. Otherwise, excessive pressure will cause damage to the differential pressure regulator.

动态压差平衡阀始终安装于回水管上，当与静态平衡阀配合使用时，如下图所示静态平衡阀安装与供水管  RETZ dynamic differential pressure balance valve is always installed on the return pipe. When used with the static balance valve, the static balance valve is installed on the water supply pipe as shown in the following figure

①-动态压差平衡阀 Dynamic differential pressure balancing valve

②-静态平衡阀 Static balancing valve

③-电动调节阀 Electric control valve